Print | Rate this content

HP Color LaserJet and LaserJet Series Products - Current Products Reference Page

This document provides specifications (see tables below) and test/reset information for current HP Color LaserJet and LaserJet series products.

NOTE: The expected life of the print cartridges is based on five percent coverage on letter-sized paper.
NOTE: Not all printer drivers are available with all operating systems.

HP Color LaserJet 2500 series printer specifications

Product (Part number)
Duty cycle
Driver languages
Paper trays
Connectivity
Print cartridges
Standard memory
HP LaserJet 2500L series printer
(C9705A)
30,000 pages over the life of the product
PCL5c
PCL6
PostScript 3 Emulation
125-sheet multi-purpose tray
250-sheet tray (optional)
500-sheet tray (optional)
IEEE-1284B Parallel
USB 1.1
HP Jetdirect 615n EIO print server (optional)
Black - C9700A
Cyan - C9701A
Yellow - C9702A
Magenta - C9703A
64 MB Expandable to 256 MB using 32-, 64-, or 128- MB DIMMs
HP LaserJet 2500 series printer
(C9706A)
30,000 pages over the life of the product
PCL5c
PCL6
PostScript 3 Emulation
125-sheet multi-purpose tray
250-sheet tray
500-sheet tray (optional)
IEEE-1284B Parallel
USB 1.1
HP Jetdirect 615n EIO print server (optional)
Black - C9700A
Cyan - C9701A
Yellow - C9702A
Magenta - C9703A
64 MB Expandable to 256 MB using 32-, 64-, or 128- MB DIMMs
HP LaserJet 2500n series printer (C9707A)
30,000 pages over the life of the product
PCL5c
PCL6
PostScript 3 Emulation
125-sheet multi-purpose tray
250-sheet tray (optional)
500-sheet tray
IEEE-1284B Parallel
USB 1.1
HP Jetdirect 615n EIO print server (optional)
Black - C9700A
Cyan - C9701A
Yellow - C9702A
Magenta - C9703A
64 MB Expandable to 256 MB using 32-, 64-, or 128- MB DIMMs
HP LaserJet 2500tn series printer (C9708A)
30,000 pages over the life of the product
PCL5c
PCL6
PostScript 3 Emulation
125-sheet multi-purpose tray
250-sheet tray
500-sheet tray
IEEE-1284B Parallel
USB 1.1
HP Jetdirect 615n EIO print server (optional)
Black - C9700A
Cyan - C9701A
Yellow - C9702A
Magenta - C9703A
64 MB Expandable to 256 MB using 32-, 64-, or 128- MB DIMMs

Demo page

To print the Demo page, press the GO button when the printer is in the Ready state and not printing.

Configuration page

Simultaneously press and release the GO and JOB CANCEL buttons at the printer control panel to print a Configuration page, supplies status page, and the HP Jetdirect Configuration page (if installed).

Cold reset

Turn the printer off, press and hold the GO button, turn the printer back on, continue holding the GO button for a minimum of five seconds and a maximum of 15 seconds, after the Go, Attention, and Ready LEDs turn on, and then release the GO button. During this process, the Attention LED will turn off, the LEDs will begin to cycle, and the unit will perform a cold reset until the printer returns to the Ready state.

NOTE: If either the Go or Ready light turn off or no LEDs turn off before the GO button is released, repeat the process.

HP LaserJet 1000 series printer information

Product
Duty cycle
Driver languages
Paper trays
Connectivity
Print cartridges
Standard memory
HP LaserJet 1000 series printer (Q1342A)
7,000 ppm
Host-based PCL5e and MS-DOS emulation
250-sheet input tray
USB cable
C7115A - 2,500 pages
32 KB ROM; 1 MB RAM

Engine test

To print an engine test page, press the engine test button with a non-metallic object. The engine test button is located beneath the cable pod connector assembly on the left-rear side of the printer. The engine test prints a striped page.

HP LaserJet 1150 series printer information

Product
Driver languages
Paper trays
Connectivity
Print cartridges
Standard memory
HP LaserJet 1150 series printer (Q1336A)
PCL5e Host-based printing
250-sheet enclosed input tray
10-sheet priority input tray
USB
1284-B Parallel port
UltraPrecise 2500-page print cartridge (Q2624-67901))
8 MB RAM

Configuration page

When the printer is in the Ready state (ready light on), press the GO button for approximately five seconds; when the Ready LED turns on, release the button.

Demo page

When the printer is in the Ready state, press and release the GO button to print a Demo page.

Cold reset

Turn the printer off, press and hold the GO button, turn the printer on, and continue to hold the GO button for approximately 15 seconds. Release the GO button and the printer LEDs begin cycling and will run until the printer is in the Ready state.

CAUTION: The NVRAM initialize may occur if the GO button is held down for more than 20 seconds, returning the system to the factory defaults.
NOTE: During this process, the Attention LED turns on. If the Ready LED also turns on before the GO button is released, restart the process.

HP LaserJet 1200 series printer information

Product
Driver languages
Paper trays
Connectivity
Print cartridges
Standard memory
HP LaserJet 1200 series printer (C7044A)
PCL5e
PCL6
Adobe PostScript Level 2
250-sheet main input tray
10-sheet priority input tray
Optional scanning unit (C7046A)
"B" type parallel cable
USB cable
C7115A - 2,500 pages
C7115X - 3,000 pages
8 MB RAM
8 MB ROM
HP LaserJet 1200se series printer (C7047A) - print/copy
PCL5e
PCL6
Adobe PostScript Level 2
250-sheet main input tray
10-sheet priority input tray
Optional scanning unit (C7046A)
"B" type parallel cable
USB cable
C7115A - 2,500 pages
C7115X - 3,000 pages
8 MB ROM
16 MB RAM
HP LaserJet 1200n series printer (C7048A) - print/copy
PCL5e
PCL6
Adobe PostScript Level 2
250-sheet main input tray
10-sheet priority input tray
Optional scanning unit (C7046A)
"B" type parallel cable
USB cable
HP Jetdirect C7115A
2,500 - pages
C7115X - 3,000 pages
8 MB RAM
8 MB ROM
HP LaserJet 1220 series printer (C7045A) - print/scan/copy
PCL5e
PCL6
Adobe PostScript Level 2
250-sheet main input tray
10-sheet priority input tray
"B" type parallel cable
USB cable
C7115A - 2,500 pages
C7115X - 3,000 pages
8 MB RAM
8 MB ROM
HP LaserJet 1220se series printer (C7049A) - print/scan/copy
PCL5e
PCL6
Adobe PostScript Level 2
250-sheet main input tray
10-sheet priority input tray
"B" type parallel cable
USB cable
C7115A - 2,500 pages
C7115X - 3,000 pages
8 MB RAM
8 MB ROM

Self test and Configuration page

Press the GO button when the printer is in the Ready state.

Continuous self-test

  1. Turn off the printer power.

  2. Press and hold the GO button while turning on the printer.

  3. Continue to hold the GO button until the green ready light turns on (approximately 17 seconds).

  4. Release the GO button. All lights will blink off and then start cycling when the test pages start printing.

  5. The self-test page will continue to print until the GO button is pressed again.

NOTE: When the printer is first turned back on, all lights will flash, and then there will be no light pattern for approximately ten seconds. The amber light will then turn on. After the GO button is released, all LEDs will turn off for a few seconds and then begin cycling. After cycling, the lights will all turn off and the green light will blink indicating that data is processing and the page is printing. The printer will return to the Ready state with a solid green light after the page has printed.
CAUTION: Holding the GO button for more than 20 seconds may initialize NVRAM and reset the unit to the factory defaults.

HP LaserJet 1300 series printer information

Product
Driver languages
Paper trays
Connectivity
Print cartridges
Standard memory
HP LaserJet 1300 series printer (Q1334A)
PCL6
PCL5e
PostScript 2 emulation
250-sheet main input tray
10-sheet priority feed tray
Optional additional 250-sheet input tray
1284-B Parallel port through low-cost input/output (LIO) connectivity card
USB 2.0
IEEE 802.11b wireless
UltraPrecise 2500-page print cartridge - Q2613A
UltraPrecise 4,000-page print cartridge - Q2613X
16 MB RAM Upgradeable to 80 MB
HP LaserJet 1300n series printer (Q1335A)
PCL6
PCL5e
PostScript 2 emulation
250-sheet main input tray
10-sheet priority feed tray
Optional additional 250-sheet input tray
1284-B Parallel port through low-cost input/output (LIO) connectivity card
USB 2.0
IEEE 802.11b wireless
HP Jetdirect print server
UltraPrecise 2500-page print cartridge - Q2613A
UltraPrecise 4,000-page print cartridge - Q2613X
16 MB RAM Upgradeable to 80 MB

Configuration page

When the printer is in the Ready state (ready light on), press the GO button for approximately five seconds, when the Ready LED turns on, release the button.

Demo page

When the printer is in the Ready state, press and release the GO button to print a Demo page.

Cold reset

Turn the printer off, press and hold the GO button, turn the printer on, and continue to hold the GO button for approximately 15 seconds. Release the GO button and the printer LEDs begin cycling and will run until the printer is in the Ready state.

CAUTION: The NVRAM initialize may occur if the GO button is held down for more than 20 seconds, returning the system to the factory defaults.
NOTE: During this process, the Attention LED turns on. If the Ready LED also turns on before the GO button is released, restart the process at Step 1.

HP LaserJet 2200 series printer information

Product
Driver languages
Paper trays
Connectivity
Print cartridges
Standard memory
HP LaserJet 2200d series printer (C7058A)
PCL6
Adobe PostScript Level 2 Emulation
One 500-sheet input paper tray
Optional 250-sheet input tray
Optional 500-sheet input tray
Bidirectional type "B" parallel IEEE-1284 ECP-compliant cable
USB (2.0 compliant) cable
Fast Infrared (FIR, IrDA compliant)
EIO slot for optional internal HP Jetdirect print server
C4096A - 5,000 pages
8 MB SD RAMM with two expansion slots, up to 72 MB
HP LaserJet 2200dt series printer (C7059A)
PCL6
Adobe PostScript Level 2 Emulation
One 500-sheet input paper tray
Optional 250-sheet input tray
Optional 500-sheet input tray
Bidirectional type "B" parallel IEEE-1284 ECP-compliant cable
USB (2.0 compliant) cable
Fast Infrared (FIR, IrDA compliant)
EIO slot for optional internal HP Jetdirect 610n print server for Ethernet 10/100Base-TX (RJ-45 port)
C4096A - 5,000 pages
8 MB SD RAMM with two expansion slots, up to 72 MB
HP LaserJet 2200dn series printer (C7063A)
PCL6
Adobe PostScript Level 2 Emulation
One 500-sheet input paper tray
Optional 250-sheet input tray
Optional 500-sheet input tray
Bidirectional type "B" parallel IEEE-1284 ECP-compliant cable
USB (2.0 compliant) cable
Fast Infrared (FIR, IrDA compliant)
EIO slot for optional internal HP Jetdirect 610n print server for Ethernet 10/100Base-TX (RJ-45 port)
C4096A - 5,000 pages
8 MB SD RAMM with two expansion slots, up to 72 MB
HP LaserJet 2200dtn series printer (C7061A)
PCL6
Adobe PostScript Level 2 Emulation
One 500-sheet input paper tray
Optional 250-sheet input tray
Optional 500-sheet input tray
Bidirectional type "B" parallel IEEE-1284 ECP-compliant cable
USB (2.0 compliant) cable Fast Infrared (FIR, IrDA compliant)
EIO slot for optional internal HP Jetdirect 610n print server for Ethernet 10/100Base-TX (RJ-45 port)
C4096A - 5,000 pages
16 MB SD RAMM with one expansion slot, up to 48 MB

Demo page

Press the GO button when the printer is in the Ready state.

Self-test, Configuration, and HP Jetdirect page

Simultaneously press and release the GO and JOB CANCEL buttons when the printer is in the Ready state. The self-test/configuration page and HP Jetdirect page (if an HP Jetdirect card is installed) will print.

Continuous self-test

  1. Turn off the printer power.

  2. Press and hold the GO button while turning on the printer.

  3. Continue to hold the GO button until the Attention and Ready lights turn on.

  4. Release the GO button.

    The Ready light blinks indicating the device is in continuous self-test mode.

    The self-test page will continue to print until the JOB CANCEL button is pressed.

Engine test

  1. Insert paper into Tray 1 or Tray 2.

  2. Remove the EIO cover.

  3. Use a long, nonconductive object to press the engine-test button (under the EIO cover). A single page, containing horizontal lines will print out.

Cold reset

CAUTION: This feature will set all system parameters to the factory defaults. Remove the HP Jetdirect card or print a self-test page before performing a cold reset to prevent losing network configuration information.
  1. Turn off the printer power.

  2. Press and hold the GO or JOB CANCEL button while turning on the printer power.

  3. Continue to hold the button until the Attention light turns on.

  4. Release the button.

    The device lights will begin cycling from front to rear. The cold-reset process will run until completion and the device will go back to the Ready state.

HP LaserJet 3200 series product information

Product
Driver languages
Paper trays
Connectivity
Print cartridges
Standard memory
HP LaserJet 3200 series product (C7052A)
PCL5e
PCL6
100-sheet capacity input bin
Single sheet priority input slot
Type "C" parallel USB cables
Optional external HP Jetdirect
C4092A - 2,500 pages
8 MB
HP LaserJet 3200se series product (C7053A)
PCL5e
PCL6
100-sheet capacity input bin
Single sheet priority input slot
Type "C" parallel cable
USB cable
Optional external HP Jetdirect
C4092A - 2,500 pages
8 MB
HP LaserJet 3200M series product (C7055A)
PCL5e
PCL6
Adobe PostScript Level 2 Emulation
100-sheet capacity input bin
Single sheet priority input slot
Type "C" parallel cable
USB cables
Optional external HP Jetdirect
C4092A - 2,500 pages
16 MB

HP LaserJet 3300 series product information

Product
Driver languages
Paper trays
Connectivity
Print cartridges
Standard memory
HP LaserJet 3300mfp series product (C9134A)
PCL5e
PCL6
PostScript Level 2 emulation
250-sheet main input tray
10-sheet priority input tray
USB (1.1)
Type "B" IEEE-compliant parallel cable
Optional HP Jetdirect 310x
C7115A - 2,500
C7115X - 3,500
4 MB ROM/Flash
32 MB RAM (27 for printer, five for PC)
HP LaserJet 3310mfp series product (C9709A)
PCL5e
PCL6
PostScript Level 2 emulation
250-sheet main input tray
10-sheet priority input tray
USB (1.1)
Type "B" IEEE-compliant parallel cable
Optional HP Jetdirect 310x
C7115A - 2,500
C7115X - 3,500
4 MB ROM/Flash
32 MB RAM (27 for printer, five for PC)
HP LaserJet 3320mfp series product (C9125A)
PCL5e
PCL6
PostScript Level 2 emulation
250-sheet main input tray
10-sheet priority input tray
USB (1.1)
Type "B" IEEE-compliant parallel cable
Optional HP Jetdirect 310x
C7115A - 2,500
C7115X - 3,500
4 MB ROM/Flash
32 MB RAM (27 for printer, five for PC)
HP LaserJet 3320n mfp series product (C9151A)
PCL5e
PCL6
PostScript Level 2 emulation
250-sheet main input tray
10-sheet priority input tray
USB (1.1)
Type "B" IEEE-compliant parallel cable
HP Jetdirect 310x
C7115A - 2,500
C7115X - 3,500
4 MB ROM/Flash
32 MB RAM (27 for printer, five for PC)
HP LaserJet 3330mfp series product (C9126A)
PCL5e
PCL6
PostScript Level 2 emulation
250-sheet main input tray
10-sheet priority input tray
USB (1.1)
Type "B" IEEE-compliant parallel cable
Optional HP Jetdirect 310x
C7115A - 2,500
C7115X - 3,500
4 MB ROM/Flash
32 MB RAM (27 for printer, five for PC)

Demo page

  1. Press the MENU/ENTER button when the printer is in the Ready state.

  2. Use the < or > button to select REPORTS and then press MENU/ENTER .

  3. Use the < or > button to select DEMO PAGE and press MENU/ENTER .

Self-test, Configuration, and HP Jetdirect page

  1. Press the MENU/ENTER button.

  2. Use the < or > button to select > and press MENU/ENTER .

  3. Use the < or > button to select CONFIG REPORT and press MENU/ENTER .

Cold reset

CAUTION: This feature will set all system parameters to the factory defaults. Remove the HP Jetdirect card or print a self-test page before performing a cold reset to prevent losing configuration information.
  1. Verify that the printer is in the Ready state.

  2. Press the MENU/ENTER button.

  3. Press the < or > button until SERVICE is displayed in the control panel menu and then press MENU/ENTER .

  4. Press the < or > button until RESTORE DEFAULTS is displayed in the control panel and then press MENU/ENTER .

  5. Press MENU/ENTER a second time to confirm. The factory defaults will restore and the unit will return to the Ready state.

Provide feedback

Please rate the information on this page to help us improve our content. Thank you!