Print | Rate this content

HP ProLiant DL365 G5 Server - Overview

Product description

The HP ProLiant DL365 G5 now offers 2 new Quad-Core Opteron processor models.
2346HE (1.8GHz, 55w) and 2356 (2.3GHz, 75w) in both BTO and CTO models
Combining concentrated 1U compute power, Integrated Lights-Out management, and essential fault tolerance, the HP ProLiant DL365 G5 is optimized for space constrained installations. Quad-Cord AMD OpteronTM processors, DDR2 memory, Serial Attached SCSI (SAS) and PCI Express technology provide a high performance system ideal for the full range scale out applications. What’s more, the DL365 G5 provides all this in an ultra-dense platform with redundant power, fans, and embedded RAID capability.
System Unit
Dimensions (H x W x D)
1.70 x 16.78 x 27.75 in (4.32 x 42.62 x 70.49 cm)
Maximum (six hard drives installed, two power supply, two processor)
37 lb (16.78 kg)
No hard drives installed, one power supply, one processor
27.5 lb (12.47 kg)
Input Requirements
Rated Input Voltage
100 to 240 VAC
Rated Input Current
7.1 Amps (at 120VAC) to 3.5 Amps (240 at VAC)
Rated Input Frequency
50 to 60 Hz
Rated Input Power
852 W
BTU Rating
2910 BTU/HR (at 120 VAC); 2870 (at 240 VAC)
NOTE: The BTU rating listed is for the Rated Input Power of 585 W.
Power Specifications
To review typical system power ratings use the Power Calculator which is available via the online tool located at URL: Calculator Catalog.xls
To drill down to calculators:
- Click on: "ProLiant Servers"
- Click on the Server of interest. Example: DL365 G5
- Click on: "Power Calculator" link. (You may need to scroll down to see it)
Power Supply Output
(per power supply)
Rated Steady-State Power
700 W
System Inlet Temperature
10° to 35°C (50° to 95°F) at sea level with an altitude derating of 1.0°C per every 305 m (1.8°F per every 1000 ft) above sea level to a maximum of 3050 m (10,000 ft), no direct sustained sunlight. Maximum rate of change is 10°C/hr (18°F/hr). The upper limit may be limited by the type and number of options installed.
System performance may be reduced if operating with a fan fault or above 30°C (86°F).
-30° to 60°C - Maximum rate of change is 20°C/Hr.
10 to 90% relative humidity (Rh), 28°C maximum wet bulb temperature
5 to 95% relative humidity (Rh), 38.7°C maximum wet bulb temperature.
Acoustic Noise
Listed are the declared A-Weighted sound power levels (LWAd) and declared average bystander position A-Weighted sound pressure levels (LpAm) when the product is operating in a 23°C ambient environment. Noise emissions were measured in accordance with ISO 7779 (ECMA 74) and declared in accordance with ISO 9296 (ECMA 109).
L pAm (dBA)
6.4 BELS
L pAm (dBA)
49 dBA
Smart Array E200i Controller
Disk Drive and Enclosure Interface
3G SAS (Serial Attached SCSI)
1.5G SATA (Serial Advanced Technology Attachment)
SAS Connectors
2 internal (SFF8484) x4 wide port connectors
Cache Memory Speed
DDR-1/266 MHz provides up to 4.2 GB/s maximum bandwidth.
Server Interface
x4 2.5G PCIe provides 2GB/s maximum bandwidth.
SAS Speed
x8 3G SAS provides 2.4GB/s maximum bandwidth.
Cache Memory
40-bit 64MB or 128MB cache: ECC protection, battery-backed, and transportable
Logical Volumes Supported
Up to 32 logical volumes
Maximum Volume Capacity
3TB (6 x 500GB)
Host Memory Addressing
64-bit, supporting greater than 4GB server memory space
RAID Support
RAID 5 (Distributed Data Guarding) requires 128MB BBWC option
RAID 1+0 (Striping & Mirroring)
RAID 0 (Striping)
Upgradeable Firmware
Upgradeable Firmware
Two Embedded NC373i Multifunction Gigabit Server Adapters
Network Interface
EEE 802.3 10Base-T
IEEE 802.3ab 1000Base-T
IEEE 802.3u 100Base-TX
Data Transfer Method
PCI Express, four lanes (x4)
Network Transfer Rate
10Base-T (Half-Duplex)
10 Mb/s
10Base-T (Full-Duplex)
20 Mb/s
100Base-TX (Half-Duplex)
100 Mb/s
100Base-TX (Full-Duplex)
200 Mb/s
1000Base-TX (Half and Full-Duplex)
2000 Mb/s
Cable Support
Categories 3, 4 or 5 UTP up to 328 ft (100 m)
10/100/1000 Base-TX
Category 5 UTP up to 328 ft (100 m)
Environment-friendly Products and Approach
End-of-life Management and Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling programs in many geographic areas. For trade-in information, please go to or contact your nearest HP sales office. Products returned to HP will be recycled, recovered or disposed of in a responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to provide treatment information for each product type for use by treatment facilities. This information (product disassembly instructions) is posted on the Hewlett Packard web site at: . These instructions may be used by recyclers and other WEEE treatment facilities as well as HP OEM customers who integrate and re-sell HP equipment.


Provide feedback

Please rate the information on this page to help us improve our content. Thank you!