Print | Rate this content

HP ProLiant DL120 G5 Server - Overview

Product description

The HP ProLiant DL120 G5 Server is an entry-level rack-optimized server providing a single processor, 1U form-factor and is ideal for single-application IT infrastructure, web and edge-of-network applications.

top

Product features

Technical Specifications
System Unit
Dimensions (H x W x D)
(with bezel)
1.69 x 17.64 x 27.5 in (4.30 x 44.80 x 69.85 cm)
Weight
(approximate)
Maximum
(two hard drives, power supply, and processor installed)
32.40 lb (14.70kg)
Minimum
(one hard drive, power supply, and processor installed)
31.00lb (14.00kg)
Input Requirements
(per power supply)
Range Line Voltage
90 - 132 VAC,
180 - 264 VAC
Rated Input Current
6 A (at 100 VAC),
3 A (at 200 VAC)
Rated Input Frequency
47 to 63 Hz
Rated Input Power
<500W @115/230 VRMS (For frequency only)
BTU Rating
Maximum
1194 BTU/hr (at 115/230 VRMS)
Power Specifications
Power Supply Output
(per power supply)
Rated Steady-State Power
350 W (at 115/230 VRMS),
350 W (at 115/230 VRMS)
Maximum Peak Power
350 W (at 115/230 VRMS),
350 W (at 115/230 VRMS)
System Inlet Temperature
Operating
10° to 35°C (50° to 95°F) at sea level with an altitude derating of 1.0°C per every 300 m (1.8°F per every 1000 ft) above sea level to a maximum of 3050 m (10,000 ft), no direct sustained sunlight. Maximum rate of change is 10°C/hr (18°F/hr). The upper limit may be limited by the type and number of options installed.
System performance may be reduced if operating with a fan fault or above 30°C (86°F).
Non-operating
-30° to 60°C (-22° to 140°F). Maximum rate of change is 20°C/hr (36°F/hr).
Relative Humidity
(non-condensing)
Operating
10 to 90% relative humidity (Rh), 28°C (82.4°F) maximum wet bulb temperature, non-condensing.
Non-operating
5 to 95% relative humidity (Rh), 38.7°C (101.7°F) maximum wet bulb temperature, non-condensing.
Altitude
Operating
3050 m (10,000 ft). This value may be limited by the type and number of options installed. Maximum allowable altitude change rate is 457 m/min (1500 ft/min).
Non-operating
9144 m (30,000 ft). Maximum allowable altitude change rate is 457 m/min (1500 ft/min).
Acoustic Noise
Listed are the declared A-Weighted sound power levels (LWAd) and declared average bystander position A-Weighted sound pressure levels (LpAm) when the product is operating in a 23°C ambient environment. Noise emissions were measured in accordance with ISO 7779 (ECMA 74) and declared in accordance with ISO 9296 (ECMA 109).
Idle
LWAd
6.26 B
LpAm
43.8 dBA
Operating
LWAd
6.28 B
LpAm
44.5 dBA
Power Supply
Input voltage specifications
Rated input voltage
100 VAC to 240VAC
Input Specifications
Rated input line
90 VAC to 264 VAC
Frequency range
47 to 63 Hz
Rated input power
@ 115 V input, Rated input power = 500 W (assume output wattage=350 W
@ 230V input, Rated input power = 500 W (assume output wattage=350 W)
Rated input current
6 A, 3 A (110 V, 220 V)
Steady state power
350W (rated)
BTU Rating
1710 BTU/hr
Ambient temperature range
Operating
50° to 118° F (10° to 48° C)
Non-operating
-40° to 158° F (-40° to 70° C)
Relative humidity
(non-condensing)
Operating
55% to 85%
Non-operating
5% to 95%
Dielectric voltage withstand
Input to output
Input to ground
Maximum Wet Bulb Temperature
106.3° F (41.3° C)
Integrated Serial ATA Controller
Simultaneous drive transfer channels
4 channels
Transfer rate synchronous
(maximum theoretical)
150 MB/s per channel; 300 MB/s in RAID 0 pair
Data transfer method
Intel 82801IR Integrated Serial ATA Host Controller (non-RAID mode)
Intel 82801IR Integrated Serial ATA Host Controller (RAID Mode)
Drive support
Serial ATA
Data transfer modes
Legacy Mode
Combined Mode
Protocol
Serial ATA
Feature
NCQ (Native Command Queuing); AHCI (Advanced Host Controller Interface)
RAID levels supported
0, 1
RAID Features
Supports multiple logical volumes
Setup through ROM based Array Configuration Utility
Installation scripting support
NOTE: This controller does not support Hot Plug functions or LED functions.
RAID OS Support
Microsoft Windows Server 2003
NOTE:In order to implement integrated SATA RAID with Smart Start 7.90 on Windows 2000/2003, the use of a floppy drive is necessary.
Linux (Red Hat, SuSE, UnitedLinux)
Embedded NC105i PCIe Gigabit Server Adapter
Network Interface
10Base-T/
100Base-TX/
1000Base-TX
Combines a triple-speed IEEE 802.3TM - Compliant Media Access Controller (MAC) with a triple-speed Ethernet transceiver.
Compatibility
IEEE 802.3 10Base-T
IEEE 802.3ab 1000Base-T
IEEE 802.3u 100Base-TX
Data Transfer Method
Four lane (x4), 100MHz PCI Express Reference Clock
Network Transfer Rate
10Base-T (Half-Duplex)
10 Mb/s
10Base-T (Full-Duplex)
20 Mb/s
100Base-TX (Half-Duplex)
100 Mb/s
100Base-TX (Full-Duplex)
200 Mb/s
1000Base-TX (Half and Full-Duplex)
2000Mb/s
Connector
RJ-45 connector
Cable Support
10Base-T
Categories 3, 4 or 5 UTP; up to 328 ft (100 m)
10/100/1000Base-TX
Category 5 UTP; up to 328 ft (100 m)
Environment-friendly Products and Approach
End-of-life Management and Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling programs in many geographic areas. Click here for trade-in information or contact your nearest HP sales office. Products returned to HP will be recycled, recovered or disposed of in a responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to provide treatment information for each product type for use by treatment facilities. Click here for product disassembly instructions . These instructions may be used by recyclers and other WEEE treatment facilities as well as HP OEM customers who integrate and re-sell HP equipment.
Memory
HP ProLiant DL120 G5
Standard Memory
NOTE: One of the following depending on model:

1 GB installed (1 x 1 GB SDRAM DIMM) on Dual-Core (E2160 and 3065) models.

2 GB installed (2 x 1 GB SDRAM DIMMs) on Quad-Core (X3320) model.

Standard Memory Plus Optional Memory

Up to 8 GB memory is available with the optional installation of PC2-6400 ECC DDR2 SDRAM Memory kits.

NOTE: The chart below does not represent all possible configurations. For best performance, HP recommends dual-bank interleaved mode configurations. For dual-bank interleaved mode, DIMMs must be installed in both banks with equal bank capacities.
Memory
Slot
DIMM_CH1_C
DIMM_CH1_A
DIMM_CH2_D
DIMM_CH2_B
Mode
Optional
512 MB
Empty
512 MB
Empty
Empty
Single-bank
Standard
1 GB
Empty
1GB
Empty
Empty
Single-bank
Optional
1 GB
Empty
512MB
Empty
512MB
Dual-bank interleaved
Standard
2 GB
Empty
1GB
Empty
1G
Dual-bank interleaved
Maximum
8 GB
2 GB
2 GB
2 GB
2 GB
Dual-bank interleaved
Following are memory options available from HP:
2 GB Unbuffered PC2-6400 ECC DIMM (1 x 2 GB)
450260-B21
1 GB Unbuffered PC2-6400 ECC DIMM (1 x 1 GB)
450259-B21
512 MB Unbuffered PC2-6400 ECC DIMM (1 x 512 MB)
450258-B21

top

Provide feedback

Please rate the information on this page to help us improve our content. Thank you!