Print | Rate this content

Setting Up the Printer for a Wireless network for the HP ENVY 110 e-All-in-One Printer Series

Introduction

This document explains how to install the print drivers and other software for your printer to use it on a wireless network. If you have more than one computer on the network, install the printer software on each computer that you plan to share with the printer.

NOTE: If you have not already set up your printer, click here for instructions to set up the printer hardware , and then return to this document to set up your printer on a wireless network.

Windows XP

Follow these steps for the Windows XP operating system.

Step one: Prepare for installation

You must have the following items before you install the printer on the wireless network.

  1. Gather the following items:

    • Network name: The network name is the SSID

    • Security passphrase (WEP key or WPA)

    • A computer that is connected to the wireless network

    • Internet access (recommended): HP recommends broadband Internet access such as cable or DSL

      NOTE: Internet access is not required for you to install your printer with a wireless connection. However, you do need Internet access to use Web Services, get printer updates, and to download drivers from the HP website.
    • Your wireless-capable printer: Place it close to the computer during the installation procedure

  2. Make sure that the printer, router, and computer are all turned on, and that the computer is connected to the same wireless network you want to connect the printer to.

  3. Disconnect any USB or Ethernet cable that is connected to the printer.

  4. Optional: If you previously installed the software for a USB connection and now want to change to a wireless network connection, follow these instructions to remove the USB installation before you continue.

    1. Click Start (), click All Programs, click HP, click the folder for your printer, and then click the icon for your printer. The printer software opens.

    2. Click Printer Setup & Software Selection.

    3. Click Convert a USB connected printer to wireless or Connect a new printer (the phrase differs depending on the version of software your computer is running).

    4. Follow the on-screen instructions to set up the printer on your wireless network. Once the printer has been set up on the wireless network, there is no need to continue with the steps in this document.

Use an automated tool to help gather information

Image: Print and Scan Doctor icon
HP Print and Scan Doctor: Quickly diagnose and resolve many printing and scanning errors, network connection problems, and driver issues. Available for Windows XP and later.
Click here to get the HP Print and Scan Doctor: Download utility (6.3 MB)

Step two: Download and install the printer software

NOTE: As an alternative method to downloading the software, you can use the installation CD instead.
  1. Turn on the printer.

  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.

  3. Go to HP Drivers & Downloads .

  4. If the Welcome to HP Support page opens, follow these steps:

    1. In the Enter product name or number field, type your printer model or number.

    2. In the Questions or keywords field, type driver, and then press Enter.

      You might need to select your printer model number from a list of similar printer models.

    3. Next to the image of your printer, click the name of your printer.

      Figure 1: Example of the link to your printer homepage

      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.

  5. Select your operating system, and then click Next.

    A list of drivers and other downloads display.

  6. Scroll down the page, and then click Driver - Product Installation Software.

  7. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.

  8. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.

Step three: Connect the printer to your wireless network

The HP software installer provides steps to connect the printer to the network. Click one of the following options, depending on which screen displays.

NOTE: HP Auto Wireless Connect is only available for 120 minutes after you turn the printer on for the first time. After 120 minutes, the installation defaults to the HP software wireless setup.

Option one: HP Auto Wireless Connect

  1. Select Yes, access my router, and then click Next.

  2. Follow the on-screen instructions to complete the software installation and wireless network setup for the printer.

Option two: The 'Printer Network Connection' screen displays

  1. Read the on-screen instructions and select one of the following options.

    • If you do not know your HP product's IP address, select Not Connected - Wireless Off, and then click Next.

    • If you know your HP product's IP address, select Connected, enter your HP product's IP address, and then click Next.

  2. Follow the on-screen instructions to complete the software installation and wireless network setup for the HP Product.

Windows Vista

Follow these steps for the Windows Vista operating system.

Step one: Prepare for installation

You must have the following items before you install the printer on the wireless network.

  1. Gather the following items:

    • Network name: The network name is the SSID

    • Security passphrase (WEP key or WPA)

    • A computer that is connected to the wireless network

    • Internet access (recommended): HP recommends broadband Internet access such as cable or DSL

      NOTE: Internet access is not required for you to install your printer with a wireless connection. However, you do need Internet access to use Web Services, get printer updates, and to download drivers from the HP website.
    • Your wireless-capable printer: Place it close to the computer during the installation procedure

  2. Make sure that the printer, router, and computer are all turned on, and that the computer is connected to the same wireless network you want to connect the printer to.

  3. Disconnect any USB or Ethernet cable that is connected to the printer.

  4. Optional: If you previously installed the software for a USB connection and now want to change to a wireless network connection, follow these instructions to remove the USB installation before you continue.

    1. Click the Windows icon (), click All Programs, click HP, click the folder for your printer, and then click the icon for your printer. The printer software opens.

    2. Click Printer Setup & Software Selection.

    3. Click Convert a USB connected printer to wireless or Connect a new printer (the phrase differs depending on the version of software your computer is running).

    4. Follow the on-screen instructions to set up the printer on your wireless network. Once the printer has been set up on the wireless network, there is no need to continue with the steps in this document.

Use an automated tool to help gather information

Image: Print and Scan Doctor icon
HP Print and Scan Doctor: Quickly diagnose and resolve many printing and scanning errors, network connection problems, and driver issues. Available for Windows XP and later.
Click here to get the HP Print and Scan Doctor: Download utility (6.3 MB)

Step two: Download and install the printer software

NOTE: As an alternative method to downloading the software, you can use the installation CD instead.
  1. Turn on the printer.

  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.

  3. Go to HP Drivers & Downloads .

  4. If the Welcome to HP Support page opens, follow these steps:

    1. In the Enter product name or number field, type your printer model or number.

    2. In the Questions or keywords field, type driver, and then press Enter.

      You might need to select your printer model number from a list of similar printer models.

    3. Next to the image of your printer, click the name of your printer.

      Figure 2: Example of the link to your printer homepage

      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.

  5. Select your operating system, and then click Next.

    A list of drivers and other downloads display.

  6. Scroll down the page, and then click Driver - Product Installation Software.

  7. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.

  8. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.

Step three: Connect the printer to your wireless network

The HP software installer provides steps to connect the printer to the network. Click one of the following options, depending on which screen displays.

NOTE: HP Auto Wireless Connect is only available for 120 minutes after you turn the printer on for the first time. After 120 minutes, the installation defaults to the HP software wireless setup.

Option one: HP Auto Wireless Connect

  1. Select Yes, access my router, and then click Next.

  2. Follow the on-screen instructions to complete the software installation and wireless network setup for the printer.

Option two: The 'Printer Network Connection' screen displays

  1. Read the on-screen instructions and select one of the following options.

    • If you do not know your HP product's IP address, select Not Connected - Wireless Off, and then click Next.

    • If you know your HP product's IP address, select Connected, enter your HP product's IP address, and then click Next.

  2. Follow the on-screen instructions to complete the software installation and wireless network setup for the HP Product.

Windows 7

Follow these steps for the Windows 7 operating system.

Step one: Gather the required network setup items

You must have the following items before you install the HP printer on the wireless network.

  1. Gather the following items:

    • Network name: The network name is the SSID

    • Security passphrase (WEP key or WPA)

    • A computer that is connected to the wireless network

    • Internet access (recommended): HP recommends broadband Internet access such as cable or DSL

      NOTE: Internet access is not required for you to install your printer with a wireless connection. However, you do need Internet access to use Web Services, get printer updates, and to download drivers from the HP website.
    • Your wireless-capable printer: Place it close to the computer during the installation procedure

  2. Make sure that the printer, router, and computer are all turned on, and that the computer is connected to the same wireless network you want to connect the printer to.

  3. Disconnect any USB or Ethernet cable that is connected to the printer.

  4. Optional: If you previously installed the software for a USB connection and now want to change to a wireless network connection, follow these instructions to remove the USB installation before you continue.

    1. Click the Windows icon (), click All Programs, click HP, click the folder for your printer, and then click the icon for your printer. The printer software opens.

    2. Click Printer Setup & Software Selection.

    3. Click Convert a USB connected printer to wireless or Connect a new printer (the phrase differs depending on the version of software your computer is running).

    4. Follow the on-screen instructions to set up the printer on a wireless network. Once the printer has been set up on the wireless network, there is no need to continue with the steps in this document.

Use an automated tool to help gather information

Image: Print and Scan Doctor icon
HP Print and Scan Doctor: Quickly diagnose and resolve many printing and scanning errors, network connection problems, and driver issues. Available for Windows XP and later.
Click here to get the HP Print and Scan Doctor: Download utility (6.3 MB)

Step two: Install the printer software

NOTE: As an alternative method to downloading the software, you can use the installation CD instead.
  1. Turn on the printer.

  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.

  3. Go to HP Drivers & Downloads .

  4. If the Welcome to HP Support page opens, follow these steps:

    1. In the Enter product name or number field, type your printer model or number.

    2. In the Questions or keywords field, type driver, and then press Enter.

      You might need to select your printer model number from a list of similar printer models.

    3. Next to the image of your printer, click the name of your printer.

      Figure 3: Example of the link to your printer homepage

      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.

  5. Select your operating system, and then click Next.

    A list of drivers and other downloads display.

  6. Scroll down the page, and then click Driver - Product Installation Software.

  7. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.

  8. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.

Step three: Connect the printer to your wireless network

The HP software installer provides steps to connect the printer to the network. Click one of the following options, depending on which screen displays.

NOTE: HP Auto Wireless Connect is only available for 120 minutes after you turn the printer on for the first time. After 120 minutes, the installation defaults to the HP software wireless setup.

Option one: HP Auto Wireless Connect

  1. Select Yes, access my router, and then click Next.

  2. Follow the on-screen instructions to complete the software installation and wireless network setup for the printer.

Option two: The 'Printer Network Connection' screen displays

  1. Read the on-screen instructions and select one of the following options.

    • If you do not know your HP product's IP address, select Not Connected - Wireless Off, and then click Next.

    • If you know your HP product's IP address, select Connected, enter your HP product's IP address, and then click Next.

  2. Follow the on-screen instructions to complete the software installation and wireless network setup for the HP Product.

Windows 8

Follow these steps for the Windows 8 operating system.

NOTE: If you are not using the latest version of Windows 8, the information in this document might not match. You can get the latest version from the Microsoft Store.

Step one: Prepare for installation

You must have the following items before you install the printer on the wireless network.

  1. Gather the following items:

    • Network name: The network name is the SSID

    • Security passphrase (WEP key or WPA)

    • A computer that is connected to the wireless network

    • Internet access (recommended): HP recommends broadband Internet access such as cable or DSL

      NOTE: Internet access is not required for you to install your printer with a wireless connection. However, you do need Internet access to use Web Services, get printer updates, and to download drivers from the HP website.
    • Your wireless-capable printer: Place it close to the computer during the installation procedure

  2. Make sure that the printer, router, and computer are all turned on, and that the computer is connected to the same wireless network you want to connect the printer to.

  3. Disconnect any USB or Ethernet cable that is connected to the printer.

  4. Optional: If you previously installed the software for a USB connection and now want to change to a wireless network connection, follow these instructions to remove the USB installation before you continue.

    1. Right-click the Start button () or the lower left corner of the screen, and then click Search.

    2. In the Search box, type HP, and then click the icon for your printer. The printer software opens.

    3. Click Utilities, and then click Printer Setup & Software Selection.

    4. Click Convert a USB connected printer to wireless or Connect a new printer (the phrase differs depending on the version of software your computer is running).

    5. Follow the on-screen instructions to finish installing the software. Once the printer has been set up on the wireless network, there is no need to continue with the steps in this document.

Use an automated tool to help gather information

Image: Print and Scan Doctor icon
HP Print and Scan Doctor: Quickly diagnose and resolve many printing and scanning errors, network connection problems, and driver issues. Available for Windows XP and later.
Click here to get the HP Print and Scan Doctor: Download utility (6.3 MB)

Step two: Download and install the software

  1. Turn on the printer.

  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.

  3. Go to HP Drivers & Downloads .

  4. If the Welcome to HP Support page opens, follow these steps:

    1. In the Enter product name or number field, type your printer model or number.

    2. In the Questions or keywords field, type driver, and then press Enter.

      You might need to select your printer model number from a list of similar printer models.

    3. Next to the image of your printer, click the name of your printer.

      Figure 4: Example of the link to your printer homepage

      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.

  5. Select your operating system, and then click Next.

    A list of drivers and other downloads display.

  6. Scroll down the page, and then click Driver - Product Installation Software.

  7. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.

  8. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.

Step three: Connect the printer to your wireless network

The HP software installer provides steps to connect the printer to the network. Click one of the following options, depending on which screen displays.

NOTE: HP Auto Wireless Connect is only available for 120 minutes after you turn the printer on for the first time. After 120 minutes, the installation defaults to the HP software wireless setup.

Option one: HP Auto Wireless Connect

  1. Select Yes, access my router, and then click Next.

  2. Follow the on-screen instructions to complete the software installation and wireless network setup for the printer.

Option two: The 'Printer Network Connection' screen displays

  1. Read the on-screen instructions and select one of the following options.

    • If you do not know your HP product's IP address, select Not Connected - Wireless Off, and then click Next.

    • If you know your HP product's IP address, select Connected, enter your HP product's IP address, and then click Next.

  2. Follow the on-screen instructions to complete the software installation and wireless network setup for the HP Product.

Mac OS X v10.6 Snow Leopard

Follow these steps to install the software on a Mac running the Snow Leopard operating system.

Step one: Prepare for installation

  1. Gather the following items:

    • Network name: The network name is the SSID (Service Set Identifier).

    • Network password: The password might also be called the WEP key or WPA security passphrase.

    • A computer connected to the wireless network.

    • A USB cable (used only during installation). Do not connect the cable now.

  2. Make sure that the router and computer are turned on, and that the computer is connected to the same wireless network you want to connect the printer to. Turn on the printer and place it close to the computer and within range of the router during the setup procedure.

  3. Exit all applications running on your computer.

  4. Disconnect any USB or Ethernet cables from the printer.

  5. Optional: Follow these steps if you previously set up the printer for a USB connection and want to change to a wireless connection.

    1. Click Go in the top Menu bar, and then click Applications.

    2. Click the HP folder, and then click Device Utilities.

    3. Double-click HP Setup Assistant.

    4. Follow the instructions to change your USB connection to a wireless network connection. Once the printer has been set up on the wireless network, there is no need to continue with the steps in this document.

Step two: Install the software

  1. Turn on the printer.

  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.

  3. Go to HP Drivers & Downloads .

  4. If the Welcome to HP Support page opens, follow these steps:

    1. In the Enter product name or number field, type your printer model or number.

    2. In the Questions or keywords field, type driver, and then press Enter.

      You might need to select your printer model number from a list of similar printer models.

    3. Next to the image of your printer, click the name of your printer.

      Figure 5: Example of the link to your printer homepage

      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.

  5. Select your operating system, and then click Next.

    A list of drivers and other downloads display.

  6. Scroll down the page, and then click Driver - Product Installation Software.

  7. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.

  8. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.

Step three: Connect the printer to the network

Select one of the following options for steps to connect the printer to the network, depending on the option that displays on your computer.

NOTE: HP Auto Wireless Connect is available in most network and computer environments for 120 minutes after you turn on the printer for the first time. After 120 minutes, the wireless connection method defaults to a wireless setup using a USB connection.

Option one: HP Auto Wireless Connect (initial setup only)

  1. Select the HP Product, and then click Continue.

  2. Follow the on-screen instructions to complete the software installation and wireless network setup for the HP product.

Option two: Wireless setup using a USB connection

Follow these steps to connect your printer to the wireless network with a USB cable.

Video of connecting your wireless printer to a wireless network with a USB cable

The following video demonstrates how to connect your wireless HP printer to a wireless network through a USB cable.

If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube Non-HP site .

  1. Connect the USB cable to the HP product, and then to your computer.

  2. Select the HP product, and then click Continue.

  3. Follow the on-screen instructions to complete the software installation and wireless network setup for the HP Product.

OS X v10.7 Lion

Follow these steps to install the software on a Mac running the Lion operating system.

NOTE: Older HP software might not be compatible with OS X 10.7 Lion. Do not try to install software that supports earlier versions of the Mac operating system, either from the original printer CD or from the HP website.

Step one: Prepare for installation

  1. Gather the following items:

    • Network name: The network name is the SSID (Service Set Identifier).

    • Network password: The password might also be called the WEP key or WPA security passphrase.

    • A computer connected to the wireless network.

    • A USB cable (used only during installation). Do not connect the cable now.

  2. Make sure that the router and computer are turned on, and that the computer is connected to the same wireless network you want to connect the printer to. Turn on the printer and place it close to the computer and within range of the router during the setup procedure.

  3. Exit all applications running on your computer.

  4. Disconnect any USB or Ethernet cables from the printer.

  5. Optional: Follow these steps if you previously set up the printer for a USB connection and want to change to a wireless connection.

    1. Click Go in the top Menu bar, and then click Applications.

    2. Click the HP folder, and then click Device Utilities.

    3. Double-click HP Setup Assistant.

    4. Follow the instructions to change your USB connection to a wireless network connection. Once the printer has been set up on the wireless network, there is no need to continue with the steps in this document.

Step two: Install the software

Follow these steps to download and install the software from the HP website. Repeat these steps to install the software on each computer that will use the printer wirelessly over the same network.

NOTE: To install the software for a wireless network connection, HP recommends that you download the software from the HP website. The printer CD is not supported in Lion, and Apple Software Update does not support steps for connecting to the wireless network.
  1. Turn on the printer.

  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.

  3. Go to HP Drivers & Downloads .

  4. If the Welcome to HP Support page opens, follow these steps:

    1. In the Enter product name or number field, type your printer model or number.

    2. In the Questions or keywords field, type driver, and then press Enter.

      You might need to select your printer model number from a list of similar printer models.

    3. Next to the image of your printer, click the name of your printer.

      Figure 6: Example of the link to your printer homepage

      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.

  5. Select your operating system, and then click Next.

    A list of drivers and other downloads display.

  6. Scroll down the page, and then click Driver - Product Installation Software.

  7. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.

  8. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.

Step three: Connect the printer to the network

Select one of the following options for steps to connect the printer to the network, depending on the option that displays on your computer.

NOTE: HP Auto Wireless Connect is available in most network and computer environments for 120 minutes after you turn on the printer for the first time. After 120 minutes, the wireless connection method defaults to a wireless setup using a USB connection.

Option one: HP Auto Wireless Connect (initial setup only)

  1. Select the HP Product, and then click Continue.

  2. Follow the on-screen instructions to complete the software installation and wireless network setup for the HP product.

Option two: Wireless setup using a USB connection

Follow these steps to connect your printer to the wireless network with a USB cable.

Video of connecting your wireless printer to a wireless network with a USB cable

The following video demonstrates how to connect your wireless HP printer to a wireless network through a USB cable.

If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube Non-HP site .

  1. Connect the USB cable to the HP product, and then to your computer.

  2. Select the HP product, and then click Continue.

  3. Follow the on-screen instructions to complete the software installation and wireless network setup for the HP Product.

OS X v10.8 Mountain Lion and OS X v10.9 Mavericks

Follow these steps to install the software on a Mac running the Mountain Lion or Mavericks operating system.

NOTE: Older HP software might not be compatible with Mountain Lion or Mavericks. Do not try to install software that supports earlier versions of the Mac operating system, either from the original printer CD or from the HP website.

Step one: Prepare for installation

  1. Gather the following items:

    • Network name: The network name is the SSID (Service Set Identifier).

    • Network password: The password might also be called the WEP key or WPA security passphrase.

    • A computer connected to the wireless network.

    • A USB cable (used only during installation). Do not connect the cable now.

  2. Make sure that the router and computer are turned on, and that the computer is connected to the same wireless network you want to connect the printer to. Turn on the printer and place it close to the computer and within range of the router during the setup procedure.

  3. Exit all applications running on your computer.

  4. Disconnect any USB or Ethernet cables from the printer.

  5. Optional: Follow these steps if you previously set up the printer for a USB connection and want to change to a wireless connection.

    1. Click Go in the top Menu bar, and then click Applications.

    2. Click the HP folder, and then click Device Utilities.

    3. Double-click HP Setup Assistant.

    4. Follow the instructions to change your USB connection to a wireless network connection. Once the printer has been set up on the wireless network, there is no need to continue with the steps in this document.

Step two: Install the software

Follow these steps to download and install the software from the HP website. Repeat these steps to install the software on each computer that will use the printer wirelessly over the same network.

NOTE: To install the printer software for a wireless network connection, HP recommends that you download the software from the HP website. The printer CD is not supported in Mountain Lion or Mavericks, and Apple Software Update does not support steps for connecting to the wireless network.
  1. Turn on the printer.

  2. Disconnect the USB cable from the printer and the computer (if you already connected it). If the printer is connected to your network, leave it connected.

  3. Go to HP Drivers & Downloads .

  4. If the Welcome to HP Support page opens, follow these steps:

    1. In the Enter product name or number field, type your printer model or number.

    2. In the Questions or keywords field, type driver, and then press Enter.

      You might need to select your printer model number from a list of similar printer models.

    3. Next to the image of your printer, click the name of your printer.

      Figure 7: Example of the link to your printer homepage

      Image: Example of the link next to your printer homepage
    4. On the HP support site, click Drivers.

  5. Select your operating system, and then click Next.

    A list of drivers and other downloads display.

  6. Scroll down the page, and then click Driver - Product Installation Software.

  7. Click Download next to the full feature software and driver listed, and then follow the prompts to save the driver to your computer.

  8. Open the folder where the software file saved (usually Downloads), double-click the file, and then follow the on-screen instructions to install the software.

Step three: Connect the printer to the network

Select one of the following options for steps to connect the printer to the network, depending on the option that displays on your computer.

NOTE: HP Auto Wireless Connect is available in most network and computer environments for 120 minutes after you turn on the printer for the first time. After 120 minutes, the wireless connection method defaults to a wireless setup using a USB connection.

Option one: HP Auto Wireless Connect (initial setup only)

  1. Select the HP Product, and then click Continue.

  2. Follow the on-screen instructions to complete the software installation and wireless network setup for the HP product.

Option two: Wireless setup using a USB connection

Follow these steps to connect your printer to the wireless network with a USB cable.

Video of connecting your wireless printer to a wireless network with a USB cable

The following video demonstrates how to connect your wireless HP printer to a wireless network through a USB cable.

If you have trouble viewing the video or to view the video in a different size, click here to play the video on YouTube Non-HP site .

  1. Connect the USB cable to the HP product, and then to your computer.

  2. Select the HP product, and then click Continue.

  3. Follow the on-screen instructions to complete the software installation and wireless network setup for the HP Product.

Related links

HP ePrint
Graphic and link to HP ePrint
For additional information related to setting up and using ePrint, click here to get started with ePrint .
HP Consumer Forums
See what other customers are saying at the HP forums .

Provide feedback

Please rate the information on this page to help us improve our content. Thank you!